天富娱乐登录测试

about us
current position: HOME >> News >> Company News

Which one is better to buy a high-speed mixer?

2019-07-29
Times

With the continuous development of the vacuum feeder industry, now users'requirements for the feeder are also increasing. So what aspects should manufacturers go for production in order to make their products better meet the needs of customers, to get more extensive shopping malls, and to be better promoted? ? Buying a high-speed mixer must be a research and development focus to pay attention to. Now the volume of the feeder can be said to be small, the smaller the feeder, the more convenient it is to use, but also to better transport, clean, storage and so on, are extremely convenient. Of course, it is also very important to develop the good functions of high-speed mixer. For example, the former feeders are all directly feeding, but now they can carry out vacuum feeding. These are the progress and development of functions. What the manufacturers need to do is to take part in more functions on this basis and improve more. Use more. These are some directions that manufacturers need to pay attention to the key development. At the same time, vacuum feeder can also pay attention to some new parts, or new materials. This gesture can also enable us to announce new products.

 

How to detect the fineness of powder particles in V mixer? On this issue, let's introduce to us by Wuxi Haibo Powder Equipment Co., Ltd. Superfine Powder, Particle Size of Micro Powder, Fine Spine Method and Instrument. We can configure the testing environment according to need. As for the superfine powder production enterprises, which one needs to buy the high-speed mixer to detect the superfine powder quickly, the better and useful method is the useful particle size analyzer, which has fast effect, does not damage the sample, and can get volume distribution. It is a better instrument for the enterprise powder size detection. Next, we will introduce a summary of ultrafine powder testing methods for our reference. 1. Laser Diffraction Scattering Method for Particle Size and Fineness Detection of Ultrafine Powder, 2. Centrifugal Settlement Method for Particle Size and Fineness Detection of Ultrafine Powder Purchased by Taicang High-speed Mixer, 3. Particle Image Processor for Ultrafine Powder Size and Fineness Detection, 4. Resistance Method for Ultrafine Powder Size and Fineness Spike (Kurt particle counter)


For the punch feeder of the vacuum powder feeder, what is the change of its pressure when it is started? When the high-speed mixer starts punching successively, it is necessary to rotate the speed adjustment screw of feeder clockwise, and the slider moves slowly, so as to see whether the slider encounters nylon gasket and length fine-tuning screw when moving back and forth. When testing the vacuum powder feeder, the slider moves back and forth. If only the nylon gasket is touched and the length of the adjusting screw is not touched, the floating rod does not fall deep enough, so the guide screw of the punch needs to be gradually lowered. If the slider moves back and forth, the punch feeder only meets the length adjusting screw and does not touch the nylon gasket, which is that the floating rod falls too deep and the guide screw of the punch needs to be gradually raised. If the slider moves between the length fine-tuning screw and the nylon gasket and the distance between the two sides is equal, then the screw needs to be rotated counterclockwise to adjust the speed of the slider, so that the slider can meet the nylon gasket and the spacer ring when the slider moves back and forth. If the speed of the high-speed mixer is unchanged and the feeding interval needs to be shortened from long to short, the guide screw is first raised to reduce the falling interval of the floating rod, so that the feeding can cooperate with the punching speed.

1541661496782958.jpg

Buying a high-speed mixer is to realize the gathering and processing of raw materials, close the input, completely avoid noise, dust and hot air pollution in the workshop. In order to ensure the continuity and stability of the use of the machine, imported PLC touch screen, computer program control, full computer active control, more reliable, less manual participation, and greatly improve the product. Quality system. The central converging and feeding system adopts the active control of micro-computer converging, which realizes the 24-hour continuous feeding of granular materials. Many small computers control the shading process of each shaping machine separately. They measure accurately and mix evenly. They can change the color sensitively to meet the requirements of multi-color and multi-variety of products. According to the production of different moulding machines, the feeding quantity can be changed sensitively. The aliases of central feeding system are: mixer feeding system, powder conveying system, etc. Which one of the high-speed mixers should choose the method of fully active air pipeline for feeding, which is mostly used in the production of several extruders in parallel with each other. In such a large-scale production of extruded products workshop, the feeding system consists of a total feeding pipeline, and then several branches of pipelines are separated from the feeding hoppers of each extruder.


Recently Viewed: